First Test Flight

 August 10 2022

Today was the big day for getting the first flight completed.  The object of the flight today is to break in the Lycoming engine as per the Lycoming recommendation for a totally rebuilt engine which was not run in at a shop after rebuild.  The run in of the engine is supposed to be 2 hours of flight at 2450 rpm and leaned properly for the conditions.  During the second hour the rpm's can be varied from 2350 through to 2550 for seating of the rings to the cylinder walls.  Of course this was only if the airframe would fly as expected.  Weather conditions were just perfect with clear skies and no wind.  At 10:00 in the morning I was airborne and completed racetrack pattern flights 1.0 miles (minimum) from the active runway at my local airport.  Temperature was 20 C and flight altitude was at 6500 feet.  

Here is some additional information for those that are building this "Vision" experimental aircraft.  My engine is very similar to the Lycoming O-320 but is a 1960's variant, Lycoming O-340 build by Lycoming specifically for the Navion twin aircraft. (They only manufactured this engine for about 8 years and was replaced by the O-360).   My engine is a totally rebuilt engine with zero time on it.   It has slightly higher compression and cylinder size than the 0-320 and is rated 140 HP.  The engine performed very well and was showing an indicated airspeed of 158 knots.  Compensating for temperature and altitude on this day the true airspeed was 180 knots.  This is right where I was hoping to see  my speeds.

One of my friends agreed to be my safety person to watch over me in case of issues where my wife might have to be notified, thankfully there was no need.  The flight lasted 2.2 hours and was recorded by my Mode S Dynon transponder to FlightAware.  During the complete time of my test flight I was under the surveillance of Calgary Class C airspace radar persons.  The flight went quite well but my landings were very bad, the first a 2 bounce go around the second a 2 bounce go around and the third a 1 bounce that  sent me 45 degrees off runway stopping in the grass.  After 6 years flying my Quickie Q2 I had some ingrained landing habits I needed to get rid of.  In short this was the tendency to keep pulling back on the stick in landing to pin the tailwheel of the Quickie.  This aircraft requires a flatter approach in ground effect to lessen any tendency to cause the airframe to balloon me back up after touchdown.  More details will be given in a upcoming post.

Final Inspection of Aircraft by MDRA rep.

 June 7 2022

Today I had the final inspection completed on my aircraft by a MDRA (Minister Deligate for Recreational Aircraft) in Alberta.  I was greeted by a extremely nice fellow Jeff Duchar who flew his own amateur built aircraft down from Red Deer Alberta.  Arriving at my hangar at 0930 in the morning just as planned.  My Inspection took just under 2 hours to complete and I was offered many accolades on my workmanship.  The inspection went very smoothly and resulted in four items to be attended to.  These were two bolts to be changed, 2 cotter pins to be secured better and two placards to add to the interior.  These items were corrected the next morning and my paperwork was on it's way to Transport Canada for review and then mailing out of my new Cof A for this aircraft.  I was so very pleased with the results of todays inspection and the kindness and common fellowship of a like minded inspector like Jeff Duchar.

Brake Test and Taxi Test

 May 9 2022

Below are a couple of videos of my first rolling movement under power.

First Engine Run

 May 4 2022

Still making progress towards getting my final inspection completed this spring.  I picked my registration letters that I wanted and made up the data plate and mounted it into the VISION.   The Canadian Registration for my airplane is now completed with Transport Canada and I have the C of R in hand with registration C-GVVI.  On May 4th I made the first run up of the totally re-built Lycoming engine and it started up right away.  This I could not be more pleased about as I had replaced the original carburetor and installed a Australian Throttle Body "Rotec" unit.  I only ran the engine for about 3 minutes to make sure oil pressure, fuel pressure and instruments were all functioning.  A few days later I ran the engine again this time to see it get warmed up and then did a very short taxi test to test the brakes and the steering.  It went perfect and total time on the engine was about 15 minutes.  Then a few days later I tied down the tail to a fence post, chalked the wheels and did the Lycoming recommended run up to full power.  Five minutes at 1000 then 10 minutes at 1400 to get the engine oil to  warm up to 120-140.  Then to 1800 RPM and cycle the propeller three times then full power for a maximum of 10 seconds followed by a cool down for about 3 minutes and another full power test for 10 seconds and then cool down and full power a last time.  Such a pleasure to see the engine get maximum RPM of 2700 on each of the full power tests.

March 2022

 April 8 2022

I have received the seat covers for the interior and am very pleased with the finish.  The seats are using memory foam with two layers on the seat bottom and one layer on the back.  The upholsterer offered to inset a Logo of the word "Vision" into the seat backs and the center console arm rest and I am very pleased with how that looks.  My registration letters were confirmed with Transport Canada and I then had the lettering made up and installed onto the fuselage.  I have submitted my documentation and photo of my Data plate to Transport Canada April 2 for my Certificate of Registration.   I have yet to complete my fuel flow test and then will run the engine for  the first time in the coming couple of weeks.  

February 2022

 February 27/22

Installed the Fire extinguisher and First Aid kit and screwed the belly panel back into place.  I spent a day  draining and redoing six brake line fittings which had been weeping very slightly over a month.  At first I was going to just leave it but it kept nagging at me.  I didn't want any type of leaks, especially leaks in hard to reach locations, so was well worth the work of draining and fixing.  I installed the Control stick and wired in the PTT button.   Placed a hose clamps on the static vents, pitot hose line and the fuel air vent lines.  Tested the pitot and static lines for no leaks.  Using the computer and Avery label (sticky back and clear) sheets I made up all the required Placards required for the interior and exterior of the aircraft.  I then used a Label maker to make up all of the placards for switches and fuses on the panel.

January

January 30 2022 

This month I installed the compass into the panel and honed out the hinges for the canopy bolts as they were very tight to get into place.  Installed the new Data Plate onto the upper center of the seat back and installed safety wire onto the engine components where it was required.  Using a digital level I measured all of the control surfaces angular movement limits and recorded on a data sheet as required by MDRA (Minister Delegate Recreational Aircraft) Canada, which is required in the final paperwork of the final inspection.  I made up a Annual Inspection Check sheet for my paperwork which is also part of the final inspection.  I spent time testing all of the electrical connections to all components and have everything working properly.  Tidied up wiring throughout the cockpit and bundled wires as much as possible.  Fabricated a bracket close to the carb heat valve to hold the C-Heat cable tightly in place 8 inches back from the B-nut on the sliding cable.